Wiring up my 65t Integy

[Patella]

I just ran over to ABC and picked up the 65t that John left for me. Does anyone know if this motor has 0 timing and whether it matters when I wire it up?

thanks

Jake

[Rckcrwlr]

Re: Wiring up my 65t Integy

I just ran over to ABC and picked up the 65t that John left for me. Does anyone know if this motor has 0 timing and whether it matters when I wire it up?

thanks

Jake

Yes it is a zero...you can check the top of the bell...you will see notches...Lathe motors come set a zero

[Patella]

Re: Wiring up my 65t Integy

Awesome. Also, I suck at soldering. I have some quick connects that will work, Do you think I could get away with putting those on there and just a few drops of solder to hold them?

[Rckcrwlr]

Re: Wiring up my 65t Integy

Awesome. Also, I suck at soldering. I have some quick connects that will work, Do you think I could get away with putting those on there and just a few drops of solder to hold them?

You should solder...you could have had me or JohnatABC solder leads on it if you needed. Do what you can...

Tin the tabs and then tin the wire...you will be an expert in no time...

[Rockbound]

Re: Wiring up my 65t Integy

yeah better solder!!

[Patella]

Re: Wiring up my 65t Integy

It's alive. I actually googled "how to solder" and realized what I've been screwing up for all these years. I never tinned properly. I got it all hooked up and in, with 15/96 and it seems to be a torquey beast. Goes at about walking speed.

Now a new question arises, should I CA my hexes into the CR01 rims because now I'm afraid of stripping them out.

Again, thanks John for the motor hookup. I also picked up a 12t pinion, but thought that might be just a tad too much.

Wish I didn't have to go out tonight.

Jake

[Rockbound]

Re: Wiring up my 65t Integy

you can if you want, it wont hurt. You may or may not strip out the hex un-glued. Just make sure your wheel nuts are always tight.

[Stburr91]

Re: Wiring up my 65t Integy

It's alive. I actually googled "how to solder" and realized what I've been screwing up for all these years.

Jake

I learned how to solder by watching vids on YouTube.

Steve

[Patella]

Re: Wiring up my 65t Integy

Man this thing is torquey. It is eating up my rockpile and the 65t barely even gets warm. I wish I had some lights cuz I'd definitely do some night crawling.

Jake

[joen007]

Re: Wiring up my 65t Integy

kool i have a set of lights i could sell you

[Rockbound]

Re: Wiring up my 65t Integy

night crawlin rocks!!! i just got back with a night scale ride with lewis up at aids!! awesome time!!

[Patella]

Re: Wiring up my 65t Integy

I'm jealous. I"m half tempted to go down to the rockpile with my lantern tonight

[Rockbound]

Re: Wiring up my 65t Integy

yeah i cant get enough of running the scaler!! it is just too much fun!!

[Bustedcrawler]

Re: Wiring up my 65t Integy

I'm jealous. I"m half tempted to go down to the rockpile with my lantern tonight

Be old school tape a flashlight to your body That's how we did it in '04 then we joined the 21st century and used LEDs

[DRCMAN]

Re: Wiring up my 65t Integy

kool i have a set of lights i could sell you

Wow You are relentless